Cisco 300-080 Exam Preparation Questions – Pass With Guarantee

By | January 19, 2018

Cisco Troubleshooting Cisco IP Telephony and Video 300-080 exam preparation is now reachable without spending huge amount of money and time because the most authenticated comprehensive Cisco 300-080 exam dumps materials are available on 25% discounted price for ensured success. Cisco Certified Network Professional Collaboration 300-080 exam Practice test software enables you to practice for Cisco 300-080 exam with real exam scenarios to boost your confidence and to enable you attempt the Cisco exam with full confidence to pass.

♥♥ 2018 NEW RECOMMEND 300-080 Exam Questions ♥♥

300-080 exam questions, 300-080 PDF dumps; 300-080 exam dumps:: https://www.dumpsschool.com/300-080-exam-dumps.html (157 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 300-080 Dumps Exam Questions and Answers:

Version: 10.0
Question: 21

Refer to the exhibit.

You’re tasked with staging configuration changes to add conference bridge functionality to an existing IOS voice gateway deployment. What command is missing for the configuration to be accepted by the IOS CLI?

A. The command maximum conference-participants must be configured under the dspfarm profile.
B. The Enhanced IOS Conference Bridge is not configured in Cisco Unified Communications Manager.
C. The command dsp services dspfarm must be configured under the voice-card configuration.
D. The dspfarm command under the voice card is missing.
E. The dsp tdm pooling command under the voice-card is missing.

Answer: C

Question: 22

Refer to the exhibit.

When a call between two HQ users was being conferenced with a remote user at the BR site, the conference failed. Which configuration would be needed to solve the problem?

A. The BR_MRG must contain the transcoder device. The BR_MRGL must be assigned to the BR phones.
B. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the HQ phones.
C. A transcoder should be configured at the remote site and assigned to all remote phones through the BR_MRGL.
D. The HQ_MRG must contain the transcoder device. The HQ_MRGL must be assigned to the software conference bridge.
E. Enable the software conference bridge to support G.711 and G.729 codecs in Cisco Unified Communications Manager service parameters.

Answer: D

Question: 23

You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with Cisco Unified Communications Manager. What is causing this issue?

A. Cisco Unified Communications Manager does not support SIP gateways.
B. The gateway does not have the UC license installed.
C. The gateway does not have Cisco Unified Border Element session licensing.
D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly configured.
E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is properly configured.
F. The Cisco ISR G2 cannot be a SIP gateway.

Answer: E

Question: 24

Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
C. misconfigured route group in Cisco Unified Communications Manager
D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager

Answer: B

Question: 25

Endpoints are configured for both H.323 and SIP using the same URI and Cisco VCS settings, but the endpoints register only as H.323 endpoints. What is causing this issue?

A. A firewall is blocking all traffic from the endpoints to the Cisco VCS.
B. The Cisco VCS has no SIP domains configured.
C. The Cisco VCS is blocking the endpoints because of duplicate ID entries.
D. The endpoints do not have the SIP option key installed.
E. SIP does not work, because SIP is used for Cisco Unified Communications Manager registration only.

Answer: B

Question: 26

You are trying to register an H.323-based Cisco TelePresence system to Cisco Unified Communications Manager and a Cisco DX70 system to the Cisco VCS Control. Why do neither of the units want to register?

A. The H.323-based system needs an E164 number to register to Cisco Unified Communications Manager, and the Cisco DX70 needs to have the MAC address configured first on the Cisco VCS Control.
B. The H.323-based system needs to register to the Cisco VCS Control with an E.164 number, and the Cisco DX70 needs the TFTP address to register on the Cisco Unified Communications Manager.
C. Both systems need to register to the Cisco VCS Control, but the H.323-based system needs to have the gatekeeper setting set to “Direct.”
D. Both systems need to register to the Cisco Unified Communications Manager, as the Cisco VCS Control is used only for firewall traversal.
E. You need Cisco TelePresence Management Suite to register Cisco TelePresence systems.
F. You need Cisco TelePresence Server to register Cisco TelePresence systems.

Answer: B

New Updated 300-080 Exam Questions 300-080 PDF dumps 300-080 practice exam dumps: https://www.dumpsschool.com/300-080-exam-dumps.html