Cisco 300-115 Braindumps

Question No. 1

Which feature can protect a Layer 2 port from spoofed IP addresses?

• A. uRPF
• B. port security
• C. IP source guard
• D. DHCP snooping

Question No. 2

When SDM templates are configured, which action must be performed for the configuration to take effect?

• A. reload
• B. shutdown
• C. write memory
• D. backup config

Question No. 3

An engineer is configuring EtherChannel between two switches using PAgP. If the EtherChannel mode on

switch 1 is configured using auto, which mode on switch 2 establishes an operational EtherChannel?

• A. desirable
• B. passive
• C. active
• D. auto

Question No. 4

Which statement about the default behavior of a Cisco switch MAC address table is true?

• A. MAC addresses are not learned on extended VLANs.
• B. MAC addresses are aged out of the MAC table after 600 seconds.
• C. MAC addresses are associated with a VLAN.
• D. MAC address filtering is enabled on trunk ports.

Question No. 5

Which First Hop Redundancy Protocol is an IEEE Standard?

• A. GLBP
• B. HSRP
• C. VRRP
• D. OSPF

Question No. 6

It a switch stack is configured to used SDM templates, where are the templates stored?

• A. stack master
• B. TFTP server
• C. flash memory
• D. all stack members

Question No. 7

Which command creates a login authentication method named “login” that will primarily use RADIUS and fail over to the local user database?

• A. (config)# aaa authentication login default radius local
• B. (config)# aaa authentication login login radius local
• C. (config)# aaa authentication login default local radius
• D. (config)# aaa authentication login radius local

Question No. 8

Which two tasks must you perform to enable AAA operations with a remote security database? (Choose two)

• A. Configure network equipment to query the remote security database.
• B. Configure a user profile in the local database of each device to which the user will have access.
• C. Configure SSH to provide remote access to network equipment.
• D. Configure Cisco Discovery Protocol on all interfaces used for authentication.
• E. Configure user profiles on the remote security database.

Question No. 9

What happens spoofed packet or something like untrusted packet is detected? (Choose three)

• A. log
• B. deletes
• C. intercepts
• D. accepts
• E. discad

Question No. 10

A physical switch port is part of an EtherChannel group. What happens while the same port is configured as a SPAN destination?

• A. The port is removed from the EtherChannel group.
• B. The operation is not allowed as an EtherChannel member cannot be a SPAN source port.
• C. The port forwards traffic in the EtherChannel group and acts as a SPAN source simultaneously.
• D. The port is put in the errdisabled state and can only be re-enabled manually.

Question No. 11

Which two commands displays IP Source Guard bindings? (Choose two)

• A. show ip dhcp binding
• B. show ip source binding
• C. show ip dhcp snooping database
• D. show ip guard source
• E. show ip verify source

Question No. 12

Refer to the exhibit.

Which two statement can be derived from the output of the show standby command? (Choose two.)

• A. R2 Fai/O regains mastership when the link comes back up.
• B. R2 becomes the active router after the hold time expires.
• C. Router with IP 10.10 1 3 is active because it has a higher IP address.
• D. If Fa0/0 is shut down, the HSRP priority on R2 becomes 80.
• E. R2 is using the default HSRP hello and hold timers.

Question No. 13

What happens if an interface within channel group is configure as SPAN destination?

• A. portchannel will forward traffic to source span
• B. will not be operational
• C. the link will be in error-disable

Question No. 14

When a Layer 2 trunking EtherChannel is configured, which two attributes must match across the member ports? (Choose two)

• A. Interface Description.
• B. Spanning-tree cost.
• C. spanning-tree priority
• D. allowed VLANS
• E. trunking mode.