NetApp NS0-180 Exam Preparation Questions – Pass With Guarantee

By | December 5, 2017

NetApp Certified Storage Installation Engineer NS0-180 exam preparation is now reachable without spending huge amount of money and time because the most authenticated comprehensive NetApp NS0-180 exam dumps materials are available on 25% discounted price for ensured success. NetApp Certified Storage Installation Engineer, ONTAP NS0-180 exam Practice test software enables you to practice for NetApp NS0-180 exam with real exam scenarios to boost your confidence and to enable you attempt the NetApp exam with full confidence to pass.

Version: 9.1
Question: 1

You are preparing to install a new 4-node cluster for your customer. They want to use NetApp CN1610 cluster switches that they previously purchased.
Which software must be downloaded to ensure that you are well prepared for this installation?

A. You must download CN1610 firmware and RCF files compatible with the clustered Data ONTAP version that your customer wants to use.
B. You must download the Cisco configuration files compatible with the clustered Data ONTAP version that your customer wants to use.
C. You must download ATTO Fibre Bridge firmware.
D. You must download the System Setup tool.

Answer: A

Explanation:
Note: The following conditions must exist before installing the FASTPATH software and reference configuration file (RCF) on a NetApp CN16xx cluster switch:
* The cluster must be a fully functioning cluster. Etc.
Reference: Installing FASTPATH software and RCF files on NetApp Cluster switches, page 1
https://library.netapp.com/ecm/ecm_download_file/ECMP11694144

Question: 2

You want to support multiple tenants with duplicate IP addresses for your storage system.
Which statement is correct in this scenario?

A. You must create additional VLANs to use multiple tenants.
B. You must create an additional IPspace.
C. You cannot support multiple tenants on your storage system.
D. You must use different ports on your controller.

Answer: B

Explanation:
IPspaces enable you to configure a single Data ONTAP cluster so that it can be accessed by clients from more than one administratively separate network domain, even if those clients are using the same IP address subnet range.
Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 32

Question: 3

New Updated NS0-180 Exam Questions NS0-180 PDF dumps NS0-180 practice exam dumps: https://www.dumpsschool.com/NS0-180-exam-dumps.html(65 Questions)

What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?

A. A node that joins a cluster has a separate NTP service.
B. A node that joins a cluster automatically adopts the NTP configuration of the cluster.
C. A node that joins a cluster must be manually configured in the NTP.
D. A node that joins a cluster must reboot before running the NTP service.

Answer: B

Explanation:
A node that joins a cluster automatically adopts the NTP configuration of the cluster.
Reference: How to configure and troubleshoot NTP on clustered Data ONTAP 8.2 and later using CLI
https://kb.netapp.com/support/index?page=content&id=1014787

Question: 4

You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system.
According the NetApp, which statement is correct?

A. You cannot install five SSD shelves to one System.
B. You need at least two stacks.
C. You need at least three stacks.
D. You can put all shelves in one stack.

Answer: D

Explanation:
Up to 10 shelves are supported per stack for the DS2246, so we one stack is enough as we only have five shelves (DS2246s).
Reference: Making the Move from FC to SAS Storage
http://www.netapp.com/as/communities/tech-ontap/tot-fc-sas-1101-as.aspx

Question: 5

Which three types of interface groups are supported on NetApp storage systems? (Choose three.)

A. single mode
B. HA interconnect
C. IPspaces
D. static multimode
E. dynamic multimode

Answer: A,D,E

Explanation:
You can create three different types of interface groups on your storage system: single-mode, static multimode, and dynamic multimode interface groups.
Reference: Types of interface groups
https://library.netapp.com/ecmdocs/ECMP1196907/html/GUID-EFA72201-E035-41E2-AC53-CD81A472B5ED.html

Question: 6

You have just configured the customer’s first SVM with a LIF IP 10.0.0.10/24. The customer’s DNS IP address is 172.16.0.250 and you are unable to ping it from the NetApp storage system, but you are able to ping the gateway and everything else works.
In this scenario what is the problem?

A. You need to have the DNS server on the same subnet as the LIF IP address.
B. You need to add a static gateway to the LIFs routing group.
C. You need to have the customer check the cable.
D. You need to add an IPspace and domain broadcast to the port.

Answer: D

Explanation:
A broadcast domain resides in an IPspace, and it contains a group of network ports, potentially from many nodes in the cluster, that belong to the same layer 2 network. The ports in the group are used in an SVM for data traffic.
Reference: Clustered Data ONTAP 8.3, Network Management Guide, page 8